- - -















-
-

Tel 707.940.1506
Fax 707.935.0942

21881 8th St East
Sonoma, CA
95476, USA
-

-
707.940.1506

FIBER-BOND™ TECHNICAL DATA

Web Pages
Downloadable PDF files
Technical Data Intro
ICBO (ER #5836) Download a PDF file of ICBO/ICC-ES approval report
VelaCarb 335U Download a PDF file of VelaCarb 335U Data Sheet
VelaCarb 600U Download a PDF file of VelaCarb 600U Data Sheet
VelaGlass 875U

Download a PDF file of VelaGlass 875U Data Sheet

Veloxx LR Download a PDF file of Veloxx LR Data Sheet
Veloxx AP Download a PDF file of Veloxx AP Data Sheet
Veloxx LVP Download a PDF file of Veloxx LVP Data Sheet
Edge Carbon Spec's Download a PDF file of Edge Carbon Spec's
Edge Glass Spec's Download a PDF file of Edge Glass Spec's
Edge Installation Guide Download a PDF file of Edge Installation Guide
VELOXX AP
Veloxx AP is a two-component, 100% solids, two-phase, epoxy paste used for bonding and filling voids prior to application of the FiberBond™ Stengthening System.

Veloxx AP is a patented, ICBO/ICC-ES approved (ER #5836) part of the FiberBond™ Strengthening System, a highly engineered product for the external strengthening of concrete and masonry structures.

General information
Color Gray (Part A)
Beige (Part B)
Gray (Mixed)
Storage Conditions Store in a dry place at 40-90° F (4-32° C) out of direct sunlight.
Shelf Life 12 months in original, unopened container.
Physical Properties
Mixed Viscosity 500,000 cps @ 50° F (10° C)
150,000 cps @ 77° F (25° C)
Pot Life (1 gallon unit) 100 minutes @ 50° F (10° C)
30 minutes @ 77° F (25° C)
15 minutes @ 90° F (32° C)
Mix Ratio 100A : 38B (by weight)
10A : 4B (by volume)
Tg 130° F 54° C
Mechanical Properties (1)
Tensile Strength [ASTM D638] 8,000 psi -
Tensile Modulus [ASTM D638] 400 psi x 103 -
Elongation at Failure [ASTM D638] 3.0 % -
Hardness [Shore D] 87 -
Compressive Strength [ASTM D695] 12 ksi -
Compressive Modulus [ASTM D695] 380 ksi -
Shear Bond Strength 2.4 ksi -
Notes
(1) Neat resin properties measured at 7 days unless noted otherwise.
[Top]
Typical Uses
• Veloxx AP can be used to bond pre-cured structural elements or to fill voids and minor surface imperfections. Veloxx AP is typically hand applied using a metal or plastic trowel.

Advantages
• Developed specifically for the FiberBond™ Strengthening System for concrete and masonry structures.
• Fully compatible with Veloxx LR Laminating Resin and Veloxx LVP Low Viscosity Primer.
• Long pot life.
• Easy to mix.
• Excellent adhesion to concrete and masonry materials.
• Solvent free, VOC compliant.
• Minimum substrate and ambient temperature is 40° F.

Packaging
• Available in 1, 5 and 55 gallon units.

Storage and Handling
• Store in a dry area at 40 - 90° F (4 - 32° C) away from direct sunlight, flame, or other hazards. When properly stored the product has an indefinite shelf life.

Installation
• Detailed installation procedures for Veloxx AP are outlined in the FiberBond™ Installation Manual.
• Installation of Veloxx AP should only be performed by contractors trained and certified by Edge Structural Composites.

Safety
• Product material safety data sheets (MSDS) should be consulted during application of or when handling this product.

Related Products
The following products are typically used with Veloxx AP:
• Veloxx LR Laminating Resin
• Veloxx LVP Low Viscosity Primer
• VelaCoat Top Coats
• Velanchor Anchors
• VelaCarb XXX Carbon Fiber Sheets
• VelaGlass XXX Glass Fiber Sheets

Disclaimer/Warranty Statement
Data reported are based on testing conducted at independent testing agencies. Edge Structural Composites reserves the right to change or modify, at its discretion, and without prior notice, any of the information contained in this document.
Edge Structural Composites warrants this product to free of manufacturing defects and that it will meet the current published properties when applied per EDGE’s installation procedure and tested in accordance with ASTM standards. The user determines the suitability for use of this product assumes all risk associated with its use.

- [Top]
--
--